It is a program controlled semi conductor device (IC), which fetches,
decodes and execute instructions.
2. What are the basic units of microprocessor?
The basic units or blocks of microprocessor are ALU, an array of registers
and control unit.
3. What is a bus?
Bus is a group of conducting lines that carries data, address and control
signals.
4. Why data bus is bi-directional?
The microprocessor is to fetch (read) the data from memory or input device
for processing and after processing it has to store (write) the data to memory or output
devices. Hence the data bus is bi-directional.
5. Why data bus is bi-directional?
The address is an identification number used by the microprocessor to
identify or access a memory location or input/output device. It is an output signal from the processor. Hence the address bus is unidirectional.
6. Define machine cycle?
Machine cycle is defined as the time required to complete one operation of
accessing memory input/output, or acknowledging an external request. This cycle may consists of three to six T-states.
7. Define T-state?
T-state is defined as one subdivision of operation performed in one clock
period. These subdivisions are internal states synchronized with the system clock, and each T-state is precisely equal to one clock period.
8. What is an instruction cycle?
The sequence of operations that a processor has to carry out while
executing the instruction is called instruction cycle. Each instruction cycle of
processor contains a number of machine cycles.
9. What is fetch and execute cycle?
The instruction cycle is divided in to fetch and execute cycles. The fetch
cycle is executed to fetch the opcode from memory. The execute cycle is executed to decode the instruction and to perform the work instructed by the instruction.
10. List the flags of 8085?
There are five flags in 8085.They are sign flag, zero flag, auxiliary carry
flag, parity flag and carry flag.
11. What does memory-mapping mean?
The memory mapping is the process of interfacing memories to
microprocessor and allocating addresses to each memory locations.
12. What is opcode fetch cycle?
The opcode fetch cycle is a machine cycle executed to fetch the opcode
of an instruction stored in memory. Each instruction starts with opcode fetch machine
cycle.
13. What are the instructions used to control the interrupts?
· EI
· DI
· RIM
· SIM·
14. What is polling?
In polling, the microprocessor’s software simply checks each of the I/O
devices every so often. During this check, the microprocessor tests to see if any device needs servicing.
15. What are the different types of interrupts?
· Hardware
· Software
Hardware interrupts- The interrupts where the CPU pins are used to receive
interrupt requests , are called hardware interrupts.
Software interrupts – This interrupt is caused by the execution of the instruction.
These are special instructions supported by the microprocessor.
16. What are the types of hardware interrupts?
TRAP
RST 7.5
RST 6.5
RST 5.5
INTR
17. Difference between memory mapped I/o and I/O mapped I/o?
Memory mapped I/O I/O mapped I/O
1. In this device address is 16- bit. Thus
Ao to A15 lines are used to generate the
device address
1. In this device address is 8-bit. Thus Ao
to A7 or A8 to A15 lines are used to
generate device address.
2. MEMR and MEMW control signals
are used to control read and write I/O
operations.
2. IOR and IOW control signals are used
to control read and write I/O operations.
3. Instructions available are
LDA,STA,MOV R,M , ADD M etc
3. Instructions available are IN and OUT.
4. Data transfer is between any register
and I/O device.
4. Data transfer is between accumulator
and I/O device.
5. Decoding 16-bit address may require
more hardware.
5. Decoding 8-bit address will require
less hardware.
18. Describe the function of the following pins in 8085?
a) READY b) ALE c) IO/M d) HOLD e)SID and SOD
READY – It is used by the microprocessor to sense whether a peripheral is ready or
not for data transfer. If not, the processor waits. It is thus used to synchronize slower
peripherals to the microprocessor.
ALE – In 8085 , ADo to AD7 lines are multiplexed and lower half of address (Ao to
A7) is available only during T1 of the machine cycle. The latching of lower half
address from the multiplexed address lines by using ALE signal.
IO/M - indicates whether I/O operation or memory operation is being carried out.
HOLD – This signal indicates that another master is requesting for the use of address
bus, data bus and control bus.
SID(Serial Input Data) – This input signal is used to accept serial data bit by bit from
the external device.
SOD(Serial Output Data) – This is an output signal which enables the transmission of
serial data bit by bit to the external device.
19. Comparison between full address decoding and partial address decoding?
1. All higher address lines are decoded to
select the memory or I/O device.
1. Few higher address lines are decoded
to select the memory or I/O device.
2. More hardware is required to design
decoding logic.
2. Hardware required to design decoding
logic is less and sometimes it can be
eliminated.
3. Higher cost for decoding circuit. 3. Less cost for decoding circuit.
4. No Multiple addresses. 4. It has a advantage of multiple
addresses.
5. Used in large systems 5. Used in small systems
20. What is ALE?
The ALE (Address latch enable) is a signal used to demultiplex the
address and data lines using an external latch. It is used to enable the external latch.
21. Where is the READY signal used?
READY is an input signal to the processor, used by the memory or
input/output devices to get extra time for data transfer or to introduce wait states in
the bus cycles.
22. Give some examples of port devices used in 8085 microprocessor based system?
The various port devices used in 8085 are
8212,8155,8156,8255,8355,8755.
23. What is the need for timing diagram?
The timing diagram provides information regarding the status of various
signals, when a machine cycle is executed. The knowledge of timing diagram is essential for system designer to select matched peripheral devices like memories,latches, ports etc from a microprocessor system.
24. What operation is performed during first T-state of every machine cycle in 8085?
In 8085, during the first T-state of every machine cycle the low byte
address is latched into an external latch using ALE signal.
25. What is interrupt acknowledge cycle?
The interrupt acknowledge cycle is a machine cycle executed by 8085
processor to get the address of the interrupt service routine in order to service the interrupt device.
26. What is vectored and non-vectored interrupt?
When an interrupt is accepted, if the processor control branches to a
specific address defined by the manufacturer then the interrupt is called vectored interrupt. In Non-vectored interrupt there is no specific address for storing the interrupt service routine. Hence the interrupted device should give the address of the interrupt service routine.
27. List the software and hardware interrupts of 8085?
Software interrupts : RST 0,RST 1,RST 2,RST 3,RST 4,RST 5,RST 6,RST 7
Hardware interrupts : TRAP,RST 7.5,RST 6.5,RST 5.5, INTR.
28. What is TRAP?
The TRAP is a non-maskable interrupt of 8085. It is not disabled by
processor reset or after recognition of interrupt.
29. How clock signals are generated in 8085 and what is the frequency of the internal clock?
The 8085 has the clock generation circuit on the chip but an external
quartz crystal or LC circuit or RC circuit should be connected at the pins X1 andX2. The maximum internal clock frequency of 8085 is 3.03MHz.
30. Define stack?
Stack is a sequence of RAM memory locations defined by the
programmer.
31. What is program counter? How it is useful in program execution?
The program counter keeps track of program execution. To execute a
program the starting address of the program is loaded in program counter. The PC sends out an address to fetch a byte of instruction from memory and increments its content automatically.32. Define opcode and operand?
Opcode(operation code) is the part of an instruction that identifies a
specific operation. Operand is a part of instruction that represents a value on which the instruction acts.
33. How the 8085 processor differentiates a memory access and I/O access?
The memory access and I/O access is differentiated using IO/M signal.
The 8085 processor asserts IO/M low for memory operation and high for I/O operations.
34. When the 8085 processor checks for an interrupt?
In the second T-state of the last machine cycle of every instruction, the
8085 processor checks whether an interrupt request is made or not.
35. Why interfacing is needed for I/O devices?
Generally I/O devices are slow devices. Therefore the speed of I/O
devices does not match with the speed of microprocessor. And so an interface is provided between system bus and I/O devices.
36. What is interrupt I/O?
If the I/O device initiate the data transfer through interrupt then the I/O
is called interrupt driven I/O.
37. What is a port?
The port is a buffered I/O, which is used to hold the data transmitted
from the microprocessor to I/O devices and vice versa.
38. What is the need for interrupt controller?
The interrupt controller is employed to expand the interrupt inputs. It
can handle the interrupt request from various devices and allow one by one to the processor.
39. What is synchronous data transfer scheme?
For synchronous data transfer scheme, the processor does not check
the readiness of the device after a command have been issued for read/write operation. For this scheme the processor will request the device to get ready and then read/write to the device immediately after the request.
40. What is asynchronous data transfer scheme?
In asynchronous data transfer scheme, first the processor sends a
request to the device for read/write operation. Then the processor keeps on polling the status of the device. Once the device is ready, the processor executes a data transfer instruction to complete the process.
41. What are the internal devices of 8255?
The internal devices of 8255 are port-A, port-B, port-C. The ports can be
programmed for either input or output function in different operating modes.
42. What is USART?
The device which can be programmed to perform Synchronous or
Asynchronous serial communication is called USART (Universal Synchronous Asynchronous Receiver Transmitter). Eg: INTEL 8251
43. What is scanning in keyboard and what is scan time?
The process of sending a zero to each row of a keyboard matrix and
reading the columns for key actuation is called scanning. The scan time is the time taken by the processor to scan all the rows one by one starting from first row and coming back to the first row again.
44. What is programmable peripheral device?
If the function performed by the peripheral device can be altered or
changed by a program instruction then the peripheral device is called programmable device. It have control register. The device can be programmed by sending control word in the prescribed format to the control register.
45. What is baud rate?
The baud rate is the rate at which the serial data are transmitted. Baud rate is defined as (The time for a bit cell). In some systems one bit cell has one data bit, then the baud rate and bits/sec are same.
46. What are the tasks involved in keyboard interface?
The tasks involved in keyboard interfacing are sensing a key actuation,
Debouncing the key and generating key codes( Decoding the key). These tasks are performed software if the keyboard is interfaced through ports and they are performed by hardware if the keyboard is interfaces through 8279.
47. How a keyboard matrix is formed in keyboard interface using 8279?
The return lines, RL0 toRL7 of 8279 are used to form the columns of keyboard matrix. In decoded scan lines SL0 t0SL3 of 8279 are used to form the rows of keyboard matrix. In encoded scan mode, the output lines of external decoder are used as rows of keyboard matrix.
48. What is GPIB?
GPIB is the General Purpose interface Bus. It is used to interface the test
instruments to the system controller.
49. Advantages of differential data transfer?
1. Communication at high data rate in real world environment.
2. Differential data transmission offers superior performance.
3. Differential signals can help induced noise signals.
50. Features of INTEL 8259?
1. It manage 8 interrupt request.
2. The interrupt vector addresses are programmable.
3. The priorities of interrupts are programmable.
4. The interrupt can be masked or unmasked individually.
51. What is meant by micro controller?
A device which contains the microprocessor with integrated peripherals like
memory, serial ports, parallel ports, timer/counter, interrupt controller, data acquisition interfaces like ADC, DAC is called micro controller.
52. List the features of 8051 micro controllers?
· Single supply +5v operation using HMOS technology.
· 4096 bytes program memory on-chip.
· 128 data memory on chip.
· 4 register banks
· 2 multiple modes, 16 bit timer/counter
· Extensive Boolean processing capabilities.
· 64KB external RAM size.
· 32 bi-directional I/O lines.·
53. Explain the operating mode 0 of 8051 serial port?
In this mode serial data enters and exists through RXD, TXD outputs the
shift clock. 8-bits are transmitted or received:8-data bits(LSB first). The baud rate is fixed at 1/12 the oscillator frequency.
54. Explain the operating mode 2 of 8051 serial port?
In this mode 11 bits are transmitted (through TXD) or received (through
(RXD): a start bit(0), 8 data bits( LSB first), a programmable 9th data bit and a stop bit(1).
On transmit, the 9th data bit can be assigned the value 0 or 1. On receive, the 9th data bit go into the RB8 in special function register SCON, while the stop bit is ignored.
The baud rate is programmable to either 1/32 or 1/64 the oscillator frequency.
55. Explain the mode 3 of 8051 serial port?
In this mode, 11 bits are transmitted (through TXD) or (received (through
RXD): a start bit(0), 8 data bits(LSB first), a programmable 9th data bit and a stop
bit(1).It is same as mode 2 except the baud rate. The baud rate in mode 3 is variable.
56. Explain the interrupts of 8051 micro controller?
· External interrupt 0 (IE0) – Highest priority
· Timer interrupt 0 (TF0)
· External interrupt 1 (IE1)
· Timer interrupt 1 (TF1)
· Serial port Interrupt
Receive interrupt (RI) - lowest priority
Transmit interrupt (TI)
57. How many bytes of internal RAM and ROM supported by 8051 micro controller?
128 bytes of internal RAM and 4 bytes of ROM.
58. Define machine cycle of 8051?
8051 machine cycle consists of 6 states, S1 through S7. One state is made
up of 2 clock pulses. Thus 12 clock period constitute one machine cycle. Two clock
periods in a state is termed as phase 1 and phase 2.
59. What are the special function of port 0 of 8051?
Port 0 is used as a multiplexed low order address/data bus during the
external memory access. When ALE is enabled, the address on port 0 pins are latched
and bus is ready to act as a data bus when ALE is low.
60. What are the alternative function of port 3 of 8051?
Serial data input (P3.0), serial data output (P3.1), external interrupt 0
(P3.2), external interrupt 1 (P3.3), external input for timer 0(P3.4), external input for
timer 1 (P3.5), external memory write pulse (P3.6), external memory read (P3.7) are
the alternative functions of port 3.
61. What are the use of scratch pad area of internal RAM of 8051?
In internal RAM 80 bytes constitutes the scratch pad area. The scratch
pad bytes can be programmed as a general purpose registers.
62. What are the flags supported by 8051 controller?
· Carry flag
· Auxiliary carry flag
· Over flow flag
· General purpose user flag
· Register bank select bit one
· Register bank select bit zero
· Parity flag63. What is meant by Power-on- Reset in 8051 controller?
When RESET pin is activated, the 8051 jumps to address location
0000H. This is called as Power-on-Reset. Reset pin is considered as a sixth interrupt
source of 8051.64. What are the significance of SFRs?
SFRs denotes Special function Registers of 8051 controller. All the
controller registers such as port latches, timer register, peripheral control register,
accumulator, PC and DPTR all are available in SFR region.
65. What are the different group of instructions supported by 8051?
· Data Transfer Group
· Arithmetic Group
· Logical Group
· Branching Group
· Bit manipulation Group
66. Write a program to mask the 0th and 7th bit using 8051?
MOV A,#data
ANL A,#81
MOV DPTR,#4500
MOVX @DPTR,A
LOOP: SJMP LOOP67. List the addressing modes of 8051?
· Direct addressing
· Register addressing
· Register indirect addressing
· Implicit addressing
· Immediate addressing
· Index addressing
· Bit addressing68. Write about CALL statement in 8051?
There are two CALL instructions. They are
· LCALL(Long call)
· ACALL(Absolute call)69. Write about the jump statement?
There are three forms of jump. They are
LJMP (Long jump) – 16 bit address
AJMP(Absolute jump) – 11 bit address
SJMP (Short jump) – relative address
70. Write a program to find the 2’s complement using 8051?
MOV A, R0
CPL A
INC A71. Write a program to swap two numbers using 8051?
MOV A,# data
SWAP A
72. Write a program to subtract two numbers & exchange the digits using 8051?
MOV A,#9F
MOV R0,#40
SUBB A,R0
SWAP A
73. What are the different types of Address decoding Techniques?
Absolute decoding/Full decoding
Linear decoding/Partial decoding
74. Comparison between full address decoding and Partial address decoding?
refer question no.19
75. What is the significance of wait state generator?
This is used to transfer data between slower I/O device and the
microprocessor. In some applns, the speed of I/O systems is not compatible with the
microprocessor’s timings. So the microprocessor has to confirm whether the peripheral is ready or not. If READY pin is high, the peripheral is ready otherwise 8085 enters in to wait state.
76. What is a Non-maskable interrupt?
It is unaffected by any mask or interrupt enable. Eg: TRAP
77. What is a Data pointer register?
The data pointer register (DPTR) consists of a high byte(DPH) and a low
byte (DPL) functions to hold 16 bit address. It may be manipulated as a 16-bit data
register or as independent 8-bit registers. It serves as a base register in indirect jumps,
look up table instructions and external data transfer.
78. What are the operating modes of 8279?
1. Input modes
· Scanned keyboard
· Scanned sensor matrix
· Strobed input
2. Display modes
· Left entry (Type writer mode)
· Right entry (Calculator mode)
79. What are the different functional units in 8279?
CPU interface section
Keyboard section
Display section
Scan section
80. What are the priority modes in 8259?
a. Fully nested mode
b. Special fully nested mode
c. Rotating Priority mode
d. Special Masked mode
e. Polled mode
81. What is IMR(Interrupt mask register)?
IMR stores the masking bits of the interrupt lines to be masked. This
register can be programmed by an operation command word (OCW).
82. What is priority resolver?
It determines the priorities of the bits set in the Interrupt request
register (IRR).The bit corresponding to the highest priority interrupt input is set in the
ISR during INTA input.
83. What is the use of IRR?
The interrupt request register is used to store all the interrupt levels
which are requesting the service. The eight interrupt inputs sets corresponding bits of
the Interrupt Request Register upon the service request.
84. What is Interrupt service register(ISR)?
The interrupt service register stores all the levels that are currently being
serviced.
85. What is the difference between SHLD and LHLD?
SHLD- Store HL register pair in memory.
This instruction is used to store the contents of H and L register directly in to memory.
LHLD- Load HL register pair from memory.
This instruction copies the contents of memory location given with in the
instruction in to the L register and the contents of next memory location in to the H
register.
86. What is the difference between STAX and LDAX?
STAX rp – Store the contents of Accumulator register (A) in memory location whose
address is specified by BC or DE register pair.
LDAX rp – Load Accumulator register (A) with the contents of memory location
whose address is specified by BC or DE register pair.
87. Write an assembly language program to transfer data from memory block B1 to
memory block B2?
MVI C,0AH; Initialize counter
LXI H, 2200H; Initialize source memory pointer
LXI D, 2300H; Initialize destination memory pointer
Loop: MOV A,M; Get byte from source memory block
STAX D; Store byte in the destination memory block
INX H; Increment source memory pointer
INX D; Increment destination memory pointer
DCR C; Decrement counter
JNZ Loop ; If counter ¹ 0 repeat
HLT
88. What are the types of branching instructions?
1. Jump instructions
2. Call and Return instructions
3. Restart instructions
89. Write an assembly language program to add 2 BCD numbers?
LXI H,2200H; Initialize pointer
MOV A,M ; Get the first number
INX H; Increment the pointer
ADD M ; Add two numbers
DAA ; Convert HEX to valid BCD
STA 2300; store the result
HLT
90. Explain the instruction LXI rp,data (16)?
LXI rp, data(16) – Load 16 –bit immediate data to specified register pair or
stack pointer. The rp is 16 – bit register pairs such as BC, DE, HL or stack pointer.
91. Write the difference between LDA and STA instruction?
LDA – Load data in to Accumulator register(A) directly from the address specified with in the instruction.
STA – Store the contents of Accumulator register(A) to the address specified with in the instruction.
92. What are the types of rotate instructions?
RLC – Rotate Accumulator Left
RRC- Rotate Accumulator Right
RAL – Rotate Accumulator Left through Carry
RAR - Rotate Accumulator Right through Carry
93. What are the operating modes of 8255?
1. Bit set/Reset mode
2. I/O modes
a)mode 0 : Simple input/output
b)mode 1 : Input/output with handshake
c)mode 2 : Bi-directional I/O data transfer
94. What are the priority modes in 8259?
1. Fully nested mode
2. Special fully nested mode
3. Rotating priority mode
4. Special mask mode
5. Poll mode
95. What is the use of SWAP function in 8051?
SWAP A : Swap nibbles with in the Accumulator bytes.
It interchanges the low and high order nibbles of the Accumulator (bits 0-3
and bits 4-7)
96. What is SCON?
SCON is the serial port control register , which contains not only the mode
selection bits (SM0 – SM2 ,REN), but also the 9th data bit for transmit and receive
(TB8 and RB8) and the serial port interrupt bits (TI and RI).
SM0 – Serial port mode control bit 0
SM1 – Serial port mode control bit 1
SM2 – Serial port mode control bit 2
REN – Receiver enable control bit
TB8 – Transmit bit 8
RB8 – Receive bit 8
TI – Transmit Interrupt flag
RI – Receive interrupt flag
97. How we calculate the Baud rate for serial port in mode 0?
Baud Rate = Oscillator frequency/12
98. What is the significance of TXD and RXD pins in 8051?
TXD – Transmit data pin for serial port in UART mode. Clock output in shift register
mode.
RXD – Receive data pin for serial port in UART mode. Data I/O pin in shift register
mode.
99. Write two examples of Register indirect Addressing modes in 8051?
MOV A,@R0 ; Load the contents pointed by R0 in A.
ADD A,@R1 ; Add the contents of A and the contents pointed by R1.
100. What is Accumulator Register?
It is an 8 – bit register. It holds a source operand and receives the result of
the arithmetic instructions (Addition, Subtraction, Multiplication and Division)
Thanks Bro :)
ReplyDelete